![]() ![]()
I installed Ubuntu Server again - this time without the HWE kernel. I'm going to re-install Ubuntu Server again (without HWE), just to see if that still causes the problem. Inet6 xxxx::xxxx:xxxx:xxxx:xxxx/xx scope link Link/ether xx:xx:xx:xx:xx:xx brd xx:xx:xx:xx:xx:xx ![]() Here's the output for sudo ip a: 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000Ģ: enp5s0: mtu 1500 qdisc mq state UP group default qlen 1000 The outputs for sudo lspci -nn | grep eth, and sudo modprobe -v alx were empty. Here's the output for sudo lshw -c network: *-networkĬapabilities: pm pciexpress msi msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiationĬonfiguration: autonegotiation=on broadcast=yes driver=alx duplex=full ip= latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s Once the installation process completed, everything seemed to work fine. #PLUG LINK 9650 ETHERNET ADAPTER SOFTWARE INSTALL#When the installation screen came up, I decided to select Install Ubuntu Server with the HWE Kernel - instead of Install Ubuntu Server. I also decided to remove the Wireless Network Adapter for the time being - just to reduce the number of variables. So I decided to re-install Ubuntu Server. This isn't an answer, but the information might help other people. HDD: WD Blue 1TB (WD10EZEX) | Seagate 1TB (ST1000DM003) RAM: Corsair Value Select 4GB Unbuffered CL15 Motherboard: GIGABYTE GA-H270-Gaming 3 (rev. Hardware specs: OS: Ubuntu Server (version: 16.04.3) The output for sudo ip a: 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1 Insmod /lib/modules/4.4.0-87-generic/kernel/drivers/net/ethernet/atheros/alx/alx.ko The output for sudo modprobe -v alx: insmod /lib/modules/4.4.0-87-generic/kernel/drivers/net/mdio.ko Here's the output for sudo lspci -nn | grep eth: 05:00.0 Ethernet controller : Qualcomm Atheros Device (rev 10) #PLUG LINK 9650 ETHERNET ADAPTER SOFTWARE DRIVER#How do I set up / associate the driver with my device? How do I acquire that driver (if it's not already installed)? How do I figure out which driver is needed? Resources: irq:132 ioport:d000(size=256) memory:ef000000-ef003fffįrom some digging online, the UNCLAIMED status leads me to believe that a driver is not installed for or not associated with the Ethernet adapter. Product: RTL8192EE PCIe Wireless Network AdapterĬapabilities: pm msi pciexpress bus_master cap_list ethernet physical wirelessĬonfiguration: broadcast=yes driver=rtl8192ee driverversion=4.4.0-87-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn Here's the output for sudo lshw -c network: *-network UNCLAIMEDĬapabilities: pm pciexpress msi msix bus_master cap_list ![]() #PLUG LINK 9650 ETHERNET ADAPTER SOFTWARE WINDOWS 7#I've decided to temporarily enable ICS (Internet Connection Sharing) on the Ethernet port of my Windows 7 computer, but now I'm having trouble getting an internet connection over the Ethernet connection (between the Windows computer and the Ubuntu Server computer). But in order to get iwconfig, I need an internet connection. #PLUG LINK 9650 ETHERNET ADAPTER SOFTWARE DRIVERS#I believe the drivers for the wireless adapter are installed, but I need the iwconfig utility/command to configure it. I'm currently trying to set a computer with Ubuntu Server (version: 16.04.3). ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |